ASTM D5685 - 11 PDF

Search book title Enter keywords for book title search. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. There were no books found for the applied search filters. Asstm is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Enter your personal account email address to request a password reset: Copyright Compu-tecture, Inc. It is informational only and not an official — of the standard; the full text of the standard itself must be referred to for its use and application.

Author:Tezahn Voodoogor
Country:Malawi
Language:English (Spanish)
Genre:Music
Published (Last):11 September 2016
Pages:164
PDF File Size:15.61 Mb
ePub File Size:13.61 Mb
ISBN:268-7-20489-552-2
Downloads:35161
Price:Free* [*Free Regsitration Required]
Uploader:Mocage



A number in parentheses indicates the year of last reapproval. Asuperscript epsilon indicates an editorial change since the last revision or reapproval. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.

It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. NOTE 2For the purposes of this standard, ploymer does not includenatural polymers. Referenced Documents2.

Abbreviations are in accordance withTerminology D, unless otherwise indicated. The composite structure may containaggregate, granular or platelet fillers, thixotropic agents,pigments, or dyes. Thermoplastic or thermosetting liners orcoatings may be included. Current edition approved Feb. Published March Originallyapproved in Last previous edition approved in as D - United States This joining method providesan interference fit over the entire length of the bond line.

This joining method provides an interference fit atthe bottom of the socket. Thisjoining provides no interference fit. Flanges are in compliance with Specification D Pressure designations are shownin Table 1. When agreed upon betweenpurchaser and manufacturer, pressure ratings determined bytests conducted following Practice D are acceptable. NOTE 5Fittings with identical classification from different manufac-turers may not be interchangeable due to non-standardization of pipe orsocket diameter, socket length, taper angle, or combination thereof.

The composite struc-ture may contain granular or platelet fillers, thixotropic agents,pigments, or dyes. The fitting shall be as uniform ascommercially practicable in color, opacity, and other physicalproperties.

Fitting center line to end dimensions,taper angles, taper length, or combinations thereof, will varyfor non-flanged joining systems and the individual manufac-turers shall be consulted for dimensions.

Dimensions shall bemeasured in accordance with 7. Samples shall be taken frommanufactured fittings when thermal analysis testing is accom-plished by differential-scanning-chlorimeter DSC.

Test inaccordance with 7. Test Methods7. When controlled envi-ronment testing is specified, tests shall be conducted in theStandard Laboratory Atmosphere of When elevated temperaturetesting is specified, conduct the tests at the design temperature6 5. Measure flange dimensions with a micrometer orvernier calipers, or other suitable measuring devices accurateto within Diameters shall be determinedby averaging a minimum of four measurements, equally spacedcircumferentially.

Leaking past the gasket interface of flanged fittings andelastomeric sealed fittings is permissible during this test,provided the pressure is at least two times the rating when theleak occurs. The bolt torquing sequence of SpecificationD, Fig. Fittings without flanges shall be tested with the pipe they are tobe used with joined to the fitting.

Bending or shape restraintduring the test is permitted to the extent applicable to itsanticipated installed conditions. This information shall becontained in the test report.

BELIMO SY2-120MFT PDF

Popular Publishers

Nikolkree Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Note 2For the purposes of this standard, ploymer does not include natural polymers. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Historical Version s — view previous versions of standard.

CERURILE OLTULUI PDF

ASTM D5685 – 11 PDF

Zulkijas Short-term hydrostatic strength test and cyclic or static pressure test shall be performed to meet the requirements prescribed. Search book title Enter keywords for book title search. Short-term hydrostatic strength test and cyclic or static pressure test shall be performed to meet the requirements prescribed. D Practice for Conditioning Plastics for Testing. No items in cart. There were no books found for the applied search filters.

Related Articles